news
新闻中心
安泊厨具

乾丰泵业参展回顾

  • Time of issue:2020-12-18 12:46:38
  • Views:

乾丰泵业参展回顾

  • Time of issue:2020-12-18 12:46
  • Views:

乾丰泵业参展回顾

Next: None
Next: None

News

The centrifugal pump knowledge is all here!
The basic structure of the centrifugal pump is composed of six parts are impeller, pump body, pump shaft, bearing, sealing ring, packing box. 1, the impeller is the core part of the centrifugal pump, its speed is higher than the force, the blade on the impeller plays a major role, the impeller in the assembly before the static balance experiment. The inner and outer surfaces of the impeller shall be smooth to reduce the friction loss of water flow. 2, the pump body is also called the pump shell, it is the main body of the pump. Plays a supporting and fixing role, and is connected with the bearing bracket. 3, the function of the pump shaft is to connect the coupling and the motor, the torque of the motor to the impeller, so it is the main part of the transmission of mechanical energy. 4. Plain bearing uses transparent oil as lubricant and lubricates it to the oil level line. Too much oil to seep out along the pump shaft, too little bearing and overheating and burning cause accidents! During the operation of the pump, the temperature of the bearing is 85 degrees, and the general operation is about 60 degrees.
See more information 白箭头 黑箭头
Northern winter water pump anti-freezing, thawing measures
Winter comes, the air is dry and cold, and the temperature drops to below zero. Are you worried that the water pump in use is easy to freeze or even the pump body is frozen and cracked under low temperature conditions, just like in previous years? In view of this situation, xiaobian summed up the following measures for anti-freezing water pump maintenance. 1, add insulation material for the pump to prevent the pump from freezing; (Water pumps also need to wear "clothes", exposed in the cold outdoor work, we can use cotton wool, towels, waste clothes and other clothes to wrap exposed outdoor water pumps, water pipes, faucets and other water facilities, to achieve thermal insulation effect.) 2, the pump body will not be temporarily empty, when using water, to prevent the pump freezing freezing pump: 3. The doors and Windows of the basement pump room and those without hVAC are closed. The unfinished basement pump room and wind tunnel are blocked. 4. Because all pumps of our company are delivered with hose pressure test, there is water in the pump body and management valve of the factory equipment. If the equipment is not installed, please be sure to take drainage measures to prevent freezing and cracking. 5. If the pump is frozen, do not start the pump. Use hot water or boiled water to pour into the pump to internalize the ice, or heat the pump shell.
See more information 白箭头 黑箭头
Shanghai Municipal Bureau of Quality supervision: 6 batches of water pump products have been found unqualified
The Shanghai Municipal Bureau of Quality and Technical Supervision announced on its website on Monday the results of a random inspection of 70 batches of water pump products in 2015. After the inspection, six batches failed to pass the inspection. According to the introduction, water pump is listed in the national industrial products production license catalogue of products. There are a total of 74 certified manufacturing enterprises in Shanghai, of which 70 have actually received products this time, and another 4 have not received samples due to production suspension and other reasons. According to gb10395.8-2006 "Agricultural and forestry tractors and machinery Technical requirements part 8: Drainage and irrigation pumps and pump units" and other national standards and related standards, the following items of submersible pump products were tested: Overload protection, grounding measures, insulation resistance and electric pump leads to cable and stator winding resistance to voltage, electric pump efficiency, rated capacity at the time of the head, electric pump input power, pump shaft power, power factor, temperature rise within the limit, motor stator cavity water (gas) pressure test, the operation instruction content, sign/sign firmly, production license; The following items of centrifugal pump have been tested: specified point efficiency, specified point flow, head, NPSH, leakage, unit operation, vibration, noise, appearance quality, mark, license mark.
See more information 白箭头 黑箭头

在线客服代码

Time of issue:2020-07-14 00:00:00

底部-联系方式

Time of issue:2020-07-14 00:00:00
MagicView

MagicView 

Wechat

Wechat

底部-版权信息

Time of issue:2020-07-14 00:00:00
搜索